5 Reasons To Consider Being An Online Ghost Immobiliser Install Shop And 5 Reasons Not To
Autowatch Ghost Immobiliser Installation
The Ghost is the UK's most advanced aftermarket CAN bus immobiliser. It's discreet, does not use LED indicators or key fobs and is concealed in the vehicle's wiring.
It also allows the user to temporarily disable the system through Transport Mode for when they are renting out their vehicle. This guide will guide you through the installation of an Ghost immobiliser.
Professional Installation
The Autowatch Ghost immobiliser protects your car against key cloning attacks, hacking attacks and relay attacks. The system is linked directly to the ECU of your car and protected by a pin code that you choose. It is inaccessible to thieves using diagnostic scanners or other advanced methods. It is not able to be disabled with circuit cuts.
The system is easy to use, but professional installation is recommended to ensure a clean connection with the ECU of your vehicle. A certified installer from Thatcham can assist in the installation and programming of your Ghost system. They can also recommend a tracking system or alarm system to complete your vehicle's protection package.
The first step is to disconnect your battery to prevent accidental airbag deployment or short circuits. Once this is done the installer is now able to begin work. Basic hand tools can be used to ensure precise connections. A multimeter is useful to check electrical values. Insulation tape and cable tie are essential to protect connections and ensure that wiring is neat. In addition, the user's manual provides specific guidance specifically tailored to the Ghost Immobiliser model you have.
During the installation, it is important to choose the right grounding location that is free of any paint or debris. Installers should also make sure that the immobiliser's wires, CAN H and CAN L are connected to the appropriate ECU ports. Depending on the model, these wires could need to be soldered or plugged in. A top-quality connector is recommended to ensure a durable and reliable connection.
Once the install is complete, the customer can activate Transport Mode. This allows the vehicle to be used by valet parking attendants or mechanics without needing to know the pin code. To do this, the customer must press the button for service on the dashboard 5 times within 2 seconds. After this is done the system will confirm with 5 indication signals.
The Autowatch Ghost 2 immobiliser is TASSA approved and a highly efficient immobiliser. It's a great option for anyone who regularly rents out their vehicles through platforms such as Turo. Immobilisers can lower insurance costs, since it lowers the chance of theft.
Getting Started
You can't go far wrong using an autowatch immobiliser for those who want to safeguard your car from thieves. It protects your vehicle from starting even the theft or copies the key. This is due to its advanced technology, which is designed to stop the car's engine from starting without the correct PIN code is entered.
The device connects to the CAN bus network in your vehicle, allowing it to communicate with the ECU directly. It uses existing buttons on the dashboard and the steering wheel to create a unique sequence that only you can identify, making it impossible for anyone else to start your vehicle. This is the best security system that will safeguard your pride and joy and will ensure its value when you want to sell it in the future.
Installing a ghost ignition is an easy procedure, but it is important to follow the instructions carefully to avoid problems with the electrical system and malfunctions. First, you need to locate and determine a constant 12V power source as well as a good grounding point on the vehicle's chassis. After that, you are able to begin connecting the wires to the immobiliser. Make sure to use high-quality connectors and soldering methods to ensure a secure connection. Insulate the connections using heat shrink tubing or insulation tape, as well as other materials to prevent short circuits of electricity.
Once the wires are connected, you can plug in the battery and start the engine to test if the immobiliser is working. After you've confirmed that everything is working correctly then you can put the immobiliser in a secure place inside the vehicle. Make sure to hide it properly to stop thieves from getting into it.
The Ghost 2 immobiliser has been TASSA (Tracker and Aftermarket Security System Association) that means it is a top-quality deterrent to car thieves. It provides superior protection against key cloning, hacking and relay attacks, and isn't able to be disabled unless you know the code. The device is easy to use, and it can be set up to a service valet setting so that your vehicle won't be activated when you take it to an MOT or for servicing.
Wiring
The Ghost Immobiliser, a cutting technological security system, has been designed to deter theft of vehicles. It connects directly to your vehicle's CAN bus network and communicates with the ECU, making it a virtually undetectable addition to your vehicle. Ghost Immobiliser doesn't interfere with your vehicle's factory settings, unlike other aftermarket systems which require the removal of circuit elements.
The system is also undetectable by thieves using diagnostic scanners. The system doesn't send or receive radio frequency signals, but instead uses CAN data for communication with your ECU. It doesn't even require any modifications to your current key fobs.
Enter your disarm sequence (either two or one buttons) and then turn on the ignition of your car to activate the Ghost Immobiliser. The indicator will flash two times to verify that you have entered the correct code. You can now start your vehicle and drive safely.
Once installed, the Ghost Immobiliser safeguards your vehicle against hacking or key cloning, while preserving its value. If you have to surrender your car for service or valet parking The Ghost Immobiliser will be temporarily disabled in Transport Mode.
You'll require a continuous power source (12V) in addition to an earthing point to complete the installation of the Ghost immobiliser. Be sure that they are well-insulated and safe to touch. It's also recommended to use cable ties to tie and secure the wires. This reduces the risk of being tampered with by thieves. Make sure you check the exact position of these points to avoid committing a mistake, and mark them with the help of tape or a label. Check all connections for signs they are wearing out. Make sure that all connections are firmly in place, and are properly insulated. Don't forget to test your Ghost Immobiliser after the installation is completed. This will ensure that the unit is functioning correctly, and that all connections are secure and insulated. Be what is ghost immobiliser to correct any issues immediately.
Testing
The Autowatch Ghost Immobiliser is an innovative vehicle security system that seamlessly into your car's ECU to prevent the engine from starting without authorization. Its cutting-edge technology safeguards your vehicle from key cloning, hacking, and other typical tactics thieves employ to steal cars. The Ghost works in conjunction with existing alarm and tracking systems to provide the best security for your car. The Ghost's unique features and subtle design make it a popular option for car enthusiasts and security-conscious motorists alike.
It is crucial to follow the steps of installation in order to ensure the proper integration of Ghost Immobiliser. Consult the wiring diagram of your vehicle to assist you in locating and connecting the wires. You'll then need to identify the power and grounding sources. Once you've located them, you'll have to mark them to make them easy to locate during installation. It is also essential to use high-quality tools and materials. Basic hand tools can help in making connections that are precise and a multimeter can check electrical values and ensure safety. Cable ties and insulation tape will keep the connections tidy and neat. Also, a user's guide will give specific guidelines tailored to your Ghost model.
It is crucial to test the system prior to installing it. Enter the PIN code into the system and then start the vehicle. This will ensure that the immobiliser functions as intended and stop unauthorised vehicle starts. It's recommended to perform this step regularly as part of your routine inspections of your vehicle to ensure that the system is working properly.
Once the installation is complete, you can drive your vehicle with confidence. The Ghost will keep your pride and joy safe from would-be thieves and ensure that no one can escape with your car without the correct PIN code. The Ghost can be linked to an approved Thatcham tracker, which detects attempts at theft or tampering. This allows you to track your vehicle if it is stolen.
The Ghost can be used in a variety of vehicles and is compatible with the majority of major brands. Monty's Locksmith can assist you in securing your vehicle using this cutting-edge device. Contact us today to learn more about our service and installation options. We are a TASSA Installer who is registered This certification ensures that we adhere to strict standards and procedures for installing our products. This guarantees customers, insurance companies, and law enforcement agencies that all installations are done safely and properly.